Promat® SYSTEMFLOOR-T

ADVANTAGES

  • Non-combustible
  • Excellent acoustic performance
  • Excellent durability
  • Resistant to high humidity
  • Easy to paint or bond with metal or plastic laminates
  • Excellent dimensional stability
  • Easy to work with conventional wood working tools

Acoustic Floating Floor

Promat® SYSTEMFLOOR-T is an acoustic floating floor, specifically developed for thermal and acoustic performance.

Each flooring element is composed of two DRYFLOOR® boards, glued together with a 50mm overlapping system in order to allow system continuity on both length and width. The flooring must be glued using PROMACOL® MARINE glue, that is MED certified and has been designed to ensure the necessary adhesion between the floor elements.

Applications

  • Acoustic floors
General Technical Data
< #Back#

GENERAL TECHNICAL DATA

(only DRYFLOOR® boards)

Nominal Density
 kg/m3 1100 (tolerance: -/+10%)
Colour   Off-white
Bending strength (Modulus of Rupture)
Longitudinal
Transverse

 
 N/mm2
 N/mm2

   
6.2
4.5

Modulus of Elasticity
 mPA 3500
Expansion in water saturation
 mm/m ≤1.0
pH value
pH 9
Organic content
% ≤2

All physical and mechanical values are averages based on standard production and tested according to internal procedures. The typical values are given for guidance. The figures can change dependent on the test methods used. If a particular value is of prime importance for a specification, please consult Promat Technical Department.

GENERAL TECHNICAL DATA

(only DRYFLOOR® boards)

Nominal Density
 kg/m3 1100 (tolerance: -/+10%)
Colour   Off-white
Bending strength (Modulus of Rupture)
Longitudinal
Transverse

 
 N/mm2
 N/mm2

   
6.2
4.5

Modulus of Elasticity
 mPA 3500
Expansion in water saturation
 mm/m ≤1.0
pH value
pH 9
Organic content
% ≤2

All physical and mechanical values are averages based on standard production and tested according to internal procedures. The typical values are given for guidance. The figures can change dependent on the test methods used. If a particular value is of prime importance for a specification, please consult Promat Technical Department.
Additional Data
< #Back#

STANDARD DIMENSIONS

Thickness (mm) ± 0.2mm   
Length (mm) ± 1mm
Width (mm) ± 1mm
Overlap (mm) 
18
1200
650
 50

STANDARD DIMENSIONS

  
4mm steel deck + 50mm 130kg/m3 mineral wool + Promat® SYSTEMFLOOR-T
3mm aluminium deck + 50mm 130kg/m3 mineral wool + Promat® SYSTEMFLOOR-T
40mm GRP deck + 50mm 130kg/m3 mineral wool +  Promat® SYSTEMFLOOR-T
Rw (dB)
49
46
 42

4mm steel deck + 30mm floating structure (wood-cork-wood) + Promat® SYSTEMFLOOR-T
3mm aluminium deck + 30mm floating structure (wood-corkwood) + Promat® SYSTEMFLOOR-T
40 mm GRP deck + 30mm floating structure (wood-corkwood) + Promat® SYSTEMFLOOR-T
Rw (dB)
45 40
 37

STANDARD DIMENSIONS

Thickness (mm) ± 0.2mm   
Length (mm) ± 1mm
Width (mm) ± 1mm
Overlap (mm) 
18
1200
650
 50

STANDARD DIMENSIONS

  
4mm steel deck + 50mm 130kg/m3 mineral wool + Promat® SYSTEMFLOOR-T
3mm aluminium deck + 50mm 130kg/m3 mineral wool + Promat® SYSTEMFLOOR-T
40mm GRP deck + 50mm 130kg/m3 mineral wool +  Promat® SYSTEMFLOOR-T
Rw (dB)
49
46
 42

4mm steel deck + 30mm floating structure (wood-cork-wood) + Promat® SYSTEMFLOOR-T
3mm aluminium deck + 30mm floating structure (wood-corkwood) + Promat® SYSTEMFLOOR-T
40 mm GRP deck + 30mm floating structure (wood-corkwood) + Promat® SYSTEMFLOOR-T
Rw (dB)
45 40
 37
Installation Guidelines
< #Back#

INSTALLATION GUIDELINES


installation- promat-systemfloor-acoustic-floor-fire-protection

Preparation

Promat® SYSTEMFLOOR-T can be fixed on the flooring supporting structures with grid spacing of approximately 600mm centres, or laid directly onto mineral wool slabs having minimum density of 130kg/m3.

Workability

The boards can be cut by means of standard woodworking tools.

Laying of the boards

Cut the overlapping strip of boards “1” to “4” along the upper part and lay down the first elements onto the floor (figure 1). Then, cut board “5” to the appropriate dimension, removing the overlapping strip on the upper part, as for the first boards. The remaining part of the fifth board can be used as first element of the new row (top left in the above installation guidance). Proceed for the remaining area as shown in the figure 1.

Junctions

The joints are glued using Promat® SYSTEMFLOOR glue (figure 2).

Two beads of glue are laid onto each connection border. The double nozzle of the PROMAT® SYSTEMFLOOR-T glue allows ease of application. A single cartridge will be sufficient for 15-20m2 of finished floor. The glue dries in approximately 10 minutes after installation. The glued elements are then mechanically anchored by staples or screws. This operation is necessary only to allow the glue to cure during the first 24 hours. It is possible to walk/step on the floor as soon as it is laid and fixed by staples or screws. Once the glue has totally dried and hardened, any surplus glue can be removed by means of a blade or cutter.

The boards are mechanically fixed by means of staples or screws. The screws must not exceed the thickness of the supporting structure or blocks in order not to create a structural path for noise transmission.

Increasing acoustic performances

Promat® SYSTEMFLOOR-T has excellent acoustic performance, but it can be further improved by incorporating PROMASOUND® TL with mineral wool, as shown, in order to increase its acoustic insulation over a wide range of frequencies.

Finishing

Promat® SYSTEMFLOOR-T can then be finished with a range of standard floor finishes.

Figure 1 Figure 2
 installation- promat-systemfloor-acoustic-floor-fire-protection installation- promat-systemfloor-acoustic-floor-fire-protection
installation- promat-systemfloor-acoustic-floor-fire-protection  
installation- promat-systemfloor-acoustic-floor-fire-protection  
installation- promat-systemfloor-acoustic-floor-fire-protection

INSTALLATION GUIDELINES


installation- promat-systemfloor-acoustic-floor-fire-protection

Preparation

Promat® SYSTEMFLOOR-T can be fixed on the flooring supporting structures with grid spacing of approximately 600mm centres, or laid directly onto mineral wool slabs having minimum density of 130kg/m3.

Workability

The boards can be cut by means of standard woodworking tools.

Laying of the boards

Cut the overlapping strip of boards “1” to “4” along the upper part and lay down the first elements onto the floor (figure 1). Then, cut board “5” to the appropriate dimension, removing the overlapping strip on the upper part, as for the first boards. The remaining part of the fifth board can be used as first element of the new row (top left in the above installation guidance). Proceed for the remaining area as shown in the figure 1.

Junctions

The joints are glued using Promat® SYSTEMFLOOR glue (figure 2).

Two beads of glue are laid onto each connection border. The double nozzle of the PROMAT® SYSTEMFLOOR-T glue allows ease of application. A single cartridge will be sufficient for 15-20m2 of finished floor. The glue dries in approximately 10 minutes after installation. The glued elements are then mechanically anchored by staples or screws. This operation is necessary only to allow the glue to cure during the first 24 hours. It is possible to walk/step on the floor as soon as it is laid and fixed by staples or screws. Once the glue has totally dried and hardened, any surplus glue can be removed by means of a blade or cutter.

The boards are mechanically fixed by means of staples or screws. The screws must not exceed the thickness of the supporting structure or blocks in order not to create a structural path for noise transmission.

Increasing acoustic performances

Promat® SYSTEMFLOOR-T has excellent acoustic performance, but it can be further improved by incorporating PROMASOUND® TL with mineral wool, as shown, in order to increase its acoustic insulation over a wide range of frequencies.

Finishing

Promat® SYSTEMFLOOR-T can then be finished with a range of standard floor finishes.

Figure 1 Figure 2
 installation- promat-systemfloor-acoustic-floor-fire-protection installation- promat-systemfloor-acoustic-floor-fire-protection
installation- promat-systemfloor-acoustic-floor-fire-protection  
installation- promat-systemfloor-acoustic-floor-fire-protection  
installation- promat-systemfloor-acoustic-floor-fire-protection
Quality Assurance
< #Back#

QUALITY ASSURANCE

Promat products are manufactured to stringent quality control systems to assure that our customers receive materials made to the highest standards. 

Operating to these standards means that all activities, which have a bearing upon quality, are set out in written procedures. 

Systematic and thorough checks are made on all materials and their usage. Test equipment is subjected to regular checks and is referred back to national standards.

The information given in this data sheet is based on actual tests and is believed to be typical of the product. No guarantee of results is implied however, since conditions of use are beyond our control.

QUALITY ASSURANCE

Promat products are manufactured to stringent quality control systems to assure that our customers receive materials made to the highest standards. 

Operating to these standards means that all activities, which have a bearing upon quality, are set out in written procedures. 

Systematic and thorough checks are made on all materials and their usage. Test equipment is subjected to regular checks and is referred back to national standards.

The information given in this data sheet is based on actual tests and is believed to be typical of the product. No guarantee of results is implied however, since conditions of use are beyond our control.

Documents
< #Back#

Brochures

Portfolio of our best solutions for vessels

Product Data Sheets

Technical data sheets of our products

Case Studies

Our best references

Brochures

Portfolio of our best solutions for vessels

Product Data Sheets

Technical data sheets of our products

Case Studies

Our best references